News
News
Contact Us
Home > Industry information

Molex Mini-Fit Jr 4.2mm Connector Guide: Part Numbers, Current and Drop-In Equivalents

Time:2025-05-16 Views:4
Molex Mini-Fit Jr 4.2mm Connector Guide: Part Numbers, Current and Drop-In Equivalents

A designer sent us a screenshot of a Molex 39-01-2080 the other day, with a note that the distributor wanted 12 weeks and a 500-piece minimum. We quoted the same 8-pin dual-row header, factory-direct, in under a day. That's the kind of order this page is about.

Mini-Fit Jr is a 4.20mm pitch system

Before you go hunting for part numbers, nail the pitch down. Mini-Fit Jr runs on a 4.20mm pitch, which is why you'll see it written as 4.2mm on half the drawings out there. Same thing. It's the bigger, higher-current sibling of Mini-Fit Plus and the lower-current Micro-Fit 3.0, which sits at 3.0mm. If your board has 4.2mm footprints, you're in Mini-Fit Jr territory, not Micro-Fit.

The 4.20mm spacing gives it room for beefier terminals, and that's the whole point. These parts carry real current, the kind you don't trust to a 2.54mm KK header. Most Mini-Fit Jr positions are rated up to 9A per circuit depending on wire gauge, which puts them squarely in the power-delivery category.

The housing numbers you'll bump into

Molex splits Mini-Fit Jr into a few series that all cross-mate. The 5557 series is the standard plug housing, the 5559 series is the receptacle, and 39-01-2xxx is how the dual-row versions are ordered. You'll also see 39-29, 44485 and 44478 prefixes for the terminals. Here's how they line up:

Series / prefixWhat it isRowsNotes
5557Plug (male) housingSingle / dualStandard crimp housing
5559Receptacle (female) housingSingle / dualMates with 5557
39-01-2xxxDual-row plug / receptacleDual2 to 24 circuits
39-29-xxxxDual-row receptacle headerDualVertical / right-angle
44485 / 44478Female / male crimp terminalsn/a18-24 AWG, 16 AWG options

Don't get lost in the exact dash numbers. What matters when you cross-reference is pitch (4.20mm), circuit count, and row count. If those three match, our housing drops into the same footprint.

Pin count and the 39-01 breakdown

The last four digits of a 39-01 number are the position count, roughly. A 39-01-2040 is a 4-circuit dual-row plug, a 39-01-2080 is 8 circuits, and so on. The same logic runs through the 5557 line, where a 5557-08R is an 8-pin plug housing. It's not always a clean one-to-one, so send us the full Molex string and we'll match it against our inventory instead of guessing.

One thing worth flagging: Mini-Fit Jr housings have a polarization rib, and some customers order them without realizing the mating header has to match. That rib is what stops you plugging a connector in upside down, and it's baked into the footprint. Our tooling keeps the same keying, so a genuine Molex header still mates.

Current rating is where it shines

The reason people specify Mini-Fit Jr over a cheaper 2.54mm header is current. A standard Mini-Fit Jr terminal carries up to 9A per circuit with 16 AWG wire, and the system is UL rated for 600V. Compare that to a KK 254 header at 3A and you can see why power supplies, drives, and battery packs reach for the 4.2mm part. It's not a signal connector, it's a power connector that happens to also carry signal.

If you need more than 9A, you're usually looking at Mini-Fit Sr or an entirely different family like MATE-N-LOK. For everything in the 5A to 9A sweet spot, Mini-Fit Jr is the default answer, and it's why it shows up in so many ATX power supplies.

Factory-direct vs the catalog price

The branded Mini-Fit Jr line is easy to get in small quantities, but the moment you need a few thousand housings the lead time and the MOQ both climb. We make drop-in 4.2mm housings, headers, and crimp terminals in Shenzhen, and we keep the common 2, 4, 6, 8, 10 and 12-circuit parts on the shelf. Factory-direct means no distributor markup, lower MOQs, and lead times measured in days for stock parts rather than weeks.

Send us the Molex number and we'll quote the equivalent. You get the same pitch, same polarization, same mating face, just without paying for the brand premium and the long tail on delivery.

What to send us for a quote

Three things, and we can turn it around the same day: the Molex part number (or pitch, circuits, and rows if you don't have it), the wire gauge you're crimping to, and roughly how many you'll need a year. That last number changes everything, because it's the difference between off-the-shelf pricing and tooling a dedicated run for you.

FAQ

What's the difference between Mini-Fit Jr and Micro-Fit 3.0?

Pitch and current. Mini-Fit Jr is 4.20mm and handles up to 9A per circuit. Micro-Fit 3.0 is 3.0mm and lower current. They don't mate.

Is 4.2mm the same as 4.20mm?

Yes, same pitch, just rounded. If your footprint says 4.2mm, it's Mini-Fit Jr.

Can your housing mate with a genuine Molex header?

Yes. We keep the same pitch, polarization rib, and keying, so drop-in mating works.

What's the minimum order for Mini-Fit Jr equivalents?

Low. Stock parts ship in small quantities, and we'll tool a dedicated run for volume. Send us your annual usage.