News
News
Contact Us
Home > Industry information

JST XH Part Numbers Explained: XHP Housing, B2B-XH-A Header and SXH-001T-P0.6 Terminal

Time:2025-03-25 Views:10
JST XH Part Numbers Explained: XHP Housing, B2B-XH-A Header and SXH-001T-P0.6 Terminal

A drawing comes in that says "XH 6-pin." That's the whole note. Somebody now has to turn those three words into an order, and there's no such thing as one part called XH. You need a housing, a PCB header and a crimp terminal, and each of those has its own number. Get one wrong and the pieces either don't mate or the terminal won't crimp onto your wire. This page is the cross-reference we use on the shop floor to sort it out.

XH isn't one part number

First thing to get straight: the XH series is a system, not a single connector. JST splits it into three families of part numbers. There's the cable-side housing, the XHP series. There's the PCB header you solder in, either B2B-XH-A for top entry or S2B-XH-A for side entry. And there's the little crimp terminal that goes inside the housing, the SXH series. You pick one from each column. A complete order always has all three, plus the wire.

One more thing people trip on. JST calls it a 2.5 mm pitch connector. Some catalogs, including a lot of our own listings, round that to 2.54 mm. Same part, same 0.098 inch spacing. XH-2.54mm and XH 2.5mm on a drawing mean the same thing here, so don't panic when the number changes between datasheets.

Housing part numbers: XHP-2 through XHP-20

The housing is the plastic socket on the end of your wire. The number after XHP is the circuit count, plain and simple. XHP-2 is two positions, XHP-6 is six, XHP-20 is twenty. JST lists them from XHP-1 all the way up to XHP-20, though the 2 through 10 sizes are the ones we ship most. Material is white PA6, UL94V-0, rated -25°C to +85°C. There are oddballs too, like XHP-2(10.0)-U and XHP-6(5.0)-U, which are filled housings used to skip positions on a harness. If your drawing names one of those, say so up front.

Header part numbers: B2B-XH-A and S2B-XH-A

The header is what you reflow or solder onto the board. B2B-XH-A is the top-entry, straight version. S2B-XH-A is the side-entry one, used when the cable has to come out sideways. Again, the leading number is the circuit count. Here's the bit of the map we reach for most:

CircuitsCable housingTop-entry headerSide-entry header
2XHP-2B2B-XH-AS2B-XH-A
3XHP-3B3B-XH-AS3B-XH-A
4XHP-4B4B-XH-AS4B-XH-A
5XHP-5B5B-XH-AS5B-XH-A
6XHP-6B6B-XH-AS6B-XH-A
8XHP-8B8B-XH-AS8B-XH-A
10XHP-10B10B-XH-AS10B-XH-A

Suffixes matter. The "-AM" versions (B2B-XH-AM and friends) come with a mounting boss. The "-1" on an S2B-XH-A-1 marks a different retention style. And the SMT variants, like S3B-XH-SM4-TB, are a separate beast from the through-hole parts. Match the suffix to your board, not just the circuit count.

Terminal part numbers: SXH-001T-P0.6 and SXH-002T-P0.6

The terminal is the tiny metal contact that gets crimped onto the wire and clicks into the housing. SXH-001T-P0.6 is the common one, supplied on tape for a crimp machine. SXH-002T-P0.6 is the alternative gauge. SXH-001T-P0.6N is another listed variant. The -P0.6 bit refers to the plating and tape spec. These terminals cover roughly AWG #30 to #22, which works out to about 0.05 to 0.33 mm², with insulation outside diameter around 0.9 to 1.9 mm. Pick the terminal for your wire gauge first, then the housing it drops into.

The electrical numbers worth checking

XH is rated 3A at AWG #22 and 250V AC/DC, with a temperature range of -25°C to +85°C. Mounting height on the compact version is about 9.8 mm. That 3A figure is the one to watch. Folks sometimes try to push XH into a power run it wasn't meant for, then wonder why it runs warm. If you're over that, you're looking at VH (3.96 mm pitch) or a different family entirely, not a bigger XH.

Where the mix-ups happen

Most of the wrong orders we see fall into two buckets. First, someone orders the housing but forgets the terminals, or orders terminals that suit the wrong wire gauge. Second, the cable comes out sideways on the board when it should come out the top, because S2B and B2B got swapped. Neither is a hard problem. It just costs a week when you have to redo it. A screenshot of the drawing with the circuit count, entry direction and wire gauge is usually enough for us to check the whole stack.

Factory-direct XH parts, minus the brand markup

Named-brand XH parts are easy to spec and annoying to buy in volume. The lead times run long, the minimums climb, and a fair chunk of what you pay is the label. We make XH-compatible wafer and terminal assemblies in Shenzhen, 2 through 10 positions, top entry, side entry and SMT, and we hold the common counts in stock. Same 2.5 mm pitch, same mating geometry, same 3A rating. The difference is factory-direct pricing, lower MOQs and lead times counted in days. Send us the part number off your drawing and we'll quote the match against our tooling.

FAQ

What's the difference between XHP-2 and B2B-XH-A?

XHP-2 is the socket that sits on the wire. B2B-XH-A is the header soldered to the board. You need both.

Is XH 2.5mm the same as XH 2.54mm?

Yes. JST calls it 2.5 mm, some catalogs round to 2.54 mm. Same connector.

Which terminal fits XHP-6?

SXH-001T-P0.6 is the usual pick for AWG #30 to #22 wire. Match the terminal to your gauge first.

How many amps can an XH connector carry?

3A at AWG #22, 250V rated. If you need more current, move up to VH.

Can you supply XH-compatible parts at lower MOQ?

We do. Send the circuit count, entry style and part number and we'll quote a factory-direct match.